Mount a Belt Tensioning Assembly in the appropriate spot on a Shoulder Block Interior Panel.

You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the Belt Tensioning Assembly. This part should be snug but not tight – if you have to push too hard, ream the hole a bit (but not too much!)

Toggle History

Revised 2 years ago
[gallery columns="1" size="medium" ids="2021,4661,4649,4665,4651,4650"] Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center anand slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)

Revised 2 years ago
[gallery columns="1" size="medium" ids="4661,4649,2021,4665,4651,4650"]ids="2021,4661,4649,4665,4651,4650"] Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)

Revised 2 years ago
[gallery columns="1" size="medium" ids="4661,4649,2021,4651,4650"]ids="4661,4649,2021,4665,4651,4650"] Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)

Revised 2 years ago
[gallery columns="1" ids="4661,4649,2021,4651,4650" size="medium"]size="medium" ids="4661,4649,2021,4651,4650"] Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)

Revised 2 years ago
[gallery columns="1" ids="4661,4649,2021,4651,4650" size="large"]size="medium"] Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)

Revised 2 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img class="alignnone size-thumbnail wp-image-2021" title="ShoulderBlockInteriorPanel" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" width="525" height="393" /></a>[gallery columns="1" ids="4661,4649,2021,4651,4650" size="large"] Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)

Revised 2 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img class="alignnone size-thumbnail wp-image-2021" title="ShoulderBlockInteriorPanel" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" width="525" height="393" /></a> Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!) [gallery link="file" ids="4648,4649,4650,4651"]

Revised 2 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img class="alignnone size-thumbnail wp-image-2021" title="ShoulderBlockInteriorPanel" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" width="525" height="393" /></a> Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!) [gallery link="file" ids="4648,4649,4650,4651"]

Revised 2 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img class="alignnone size-thumbnail wp-image-2021" title="ShoulderBlockInteriorPanel" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" width="525" height="393" /></a> Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!) <!--more--> <div style="clear:both"> <a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.20.47.jpg"><img class="alignleft wp-image-4648 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.20.47-150x150.jpg" alt="2014-06-19 14.20.47" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.21.24-HDR.jpg"><img class="alignleft wp-image-4649 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.21.24-HDR-150x150.jpg" alt="2014-06-19 14.21.24 HDR" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.06.56-HDR.jpg"><img class="alignleft wp-image-4651 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.06.56-HDR-150x150.jpg" alt="2014-06-20 13.06.56 HDR" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.05.55-HDR.jpg"><img class="alignleft wp-image-4650 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.05.55-HDR-150x150.jpg" alt="2014-06-20 13.05.55 HDR" width="150" height="150" /></a> </div>

Revised 2 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img class="alignnone size-thumbnail wp-image-2021" title="ShoulderBlockInteriorPanel" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" width="525" height="393" /></a> Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!) <!--more--><a<!--more--> <div style="clear:both"> <a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.20.47.jpg"><img class="alignleft wp-image-4648 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.20.47-150x150.jpg" alt="2014-06-19 14.20.47" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.21.24-HDR.jpg"><img class="alignleft wp-image-4649 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.21.24-HDR-150x150.jpg" alt="2014-06-19 14.21.24 HDR" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.06.56-HDR.jpg"><img class="alignleft wp-image-4651 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.06.56-HDR-150x150.jpg" alt="2014-06-20 13.06.56 HDR" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.05.55-HDR.jpg"><img class="alignleft wp-image-4650 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.05.55-HDR-150x150.jpg" alt="2014-06-20 13.05.55 HDR" width="150" height="150" /></a> </div>

Revised 2 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img class="alignnone size-thumbnail wp-image-2021" title="ShoulderBlockInteriorPanel" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-2021" /></a> <p>MountMount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>.</p>Mount</em>. <p>YouYou should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push too hard, ream the hole a bit (but not too much!)</p>much!) <!--more--><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.20.47.jpg"><img class="alignleft wp-image-4648 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.20.47-150x150.jpg" alt="2014-06-19 14.20.47" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.21.24-HDR.jpg"><img class="alignleft wp-image-4649 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-19-14.21.24-HDR-150x150.jpg" alt="2014-06-19 14.21.24 HDR" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.06.56-HDR.jpg"><img class="alignleft wp-image-4651 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.06.56-HDR-150x150.jpg" alt="2014-06-20 13.06.56 HDR" width="150" height="150" /></a><a href="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.05.55-HDR.jpg"><img class="alignleft wp-image-4650 size-thumbnail" src="http://diylilcnc.org/wp-content/uploads/2012/03/2014-06-20-13.05.55-HDR-150x150.jpg" alt="2014-06-20 13.05.55 HDR" width="150" height="150" /></a>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-2021" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>.Mount</em>.</p> You<p>You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push totoo hard, ream the hole a bit (but not too much!)</p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-2021" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> (see below) in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push to h</p>hard, ream the hole a bit (but not too much!)</p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-2021" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> (see below) in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>.</p>Mount</em>. You should also add a rod bushing to the center hole at this time, oriented so that the lip is on the same side as the <em>Belt Tensioning Assembly</em>. This part should be snug but not tight - if you have to push to h</p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-2021" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> (see below) in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. <ol> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>Mount</em>.</p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-2018"wp-image-2021" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> (see below) in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. <ol> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg"href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel.gif"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlockInteriorPanel-525x393.gif" alt="" title="ShoulderBlock_01"title="ShoulderBlockInteriorPanel" width="525" height="393" class="alignnone size-thumbnail wp-image-1116"wp-image-2018" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> (see below) in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. <ol> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignnone size-thumbnail wp-image-1116" /></a> <p>Mount a <em>Belt Tensioning Assembly</em> (see below) in the appropriate spot on a <em>Shoulder Block Interior Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. <ol> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignnone size-thumbnail wp-image-1116" /></a> <p>Stack the following on<p>Mount a bolt and install the resulting <em>Belt TensionerTensioning Assembly</em> onin the appropriate spot on a <em>Shoulder Block Interior Panel</em> as shown.Panel</em>. The orientation of this panel is crucial: when you hold it in your hand, the <em>Belt Tensioning Assembly</em> should be left of center an slightly lower than the <em>Bushing Mount</em>. <ol> <li>M8x35 bolt</li> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignnone size-thumbnail wp-image-1116" /></a>Install one belt tensioner in Shoulder Block Interior Panel.  When you stand this panel on end,/></a> <p>Stack the tensioner will be located slightly below centerfollowing on a bolt and toinstall the right. Belt tensioners consist ofresulting <em>Belt Tensioner Assembly</em> on the following:<em>Shoulder Block Interior Panel</em> as shown. <ol> <li>M8x35 bolt</li> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignnone size-thumbnail wp-image-1116" /></a>Install one belt tensioner in Shoulder Block Panel 1. Interior Panel.  When you stand this panel on end, the tensioner will be located slightly below center and to the right. Belt tensioners consist of the following: <ol> <li>M8x35 bolt</li> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignnone size-thumbnail wp-image-1116" /></a>Install one belt tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the tensioner will be located slightly below center and to the right. Belt tensioners consist of the following: <ol> <li>M8x35 bolt</li> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol> <p>When you stand this panel on end, the tensioner will be located slightly below center and to the right. </p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignnone size-thumbnail wp-image-1116" /></a>Install one Belt Tensionerbelt tensioner in Shoulder Block Panel 1.  WhenBelt tensioners consist of the following: <ol> <li>M8x35 bolt</li> <li>large washer</li> <li>small washer</li> <li>skate bearing</li> <li>small washer</li> <li>large washer</li> <li>M8 nut</li> </ol> <p>When you stand this panel on end, the Belt Tensionertensioner will be located slightly below center and to the right. </p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignleftclass="alignnone size-thumbnail wp-image-1084" /></a> <p> Installwp-image-1116" /></a>Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. </p>

Revised 4 years ago
<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignleft size-thumbnail wp-image-1084" /></a>Install/></a> <p> Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. </p>

Revised 4 years ago
Install<a href="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01.jpg"><img src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-525x393.jpg" alt="" title="ShoulderBlock_01" width="525" height="393" class="alignleft size-thumbnail wp-image-1084" /></a>Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right.

Revised 4 years ago
&nbsp; &nbsp; Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. &nbsp; &nbsp;

Revised 4 years ago
<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"><img class="alignnone" title="hi" src="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg" alt="" width="240" height="180" /></a>&nbsp; &nbsp; <img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" />InstallInstall one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. <img class="aligncenter size-medium wp-image-903" title="ShoulderBlock_01" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-300x225.jpg" alt="" width="300" height="225" />&nbsp; <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />&nbsp;

Revised 4 years ago
<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"><img class="alignnone" title="hi" src="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg" alt="" width="240" height="180" /></a> <a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"> </a>&nbsp; <a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"></a><img<img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. <img class="aligncenter size-medium wp-image-903" title="ShoulderBlock_01" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-300x225.jpg" alt="" width="300" height="225" /> <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />

Revised 4 years ago
<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"><img class="alignnone" title="hi" src="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg" alt="" width="240" height="180" />/></a> [caption id="attachment_713" align="aligncenter" width="300" caption="1/32&quot; 6061 Aluminum"]<img class="size-medium wp-image-713" title="6061" src="http://diylilcnc.org/wp-content/uploads/2011/08/6061-300x225.jpg" alt="" width="300" height="225" />[/caption]<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"> </a> </a><img<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"></a><img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" /><img class="aligncenter size-medium wp-image-1067" title="chris2" src="http://diylilcnc.org/wp-content/uploads/2012/03/chris2-300x225.jpg" alt="" width="300" height="225" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. <img class="aligncenter size-medium wp-image-903" title="ShoulderBlock_01" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-300x225.jpg" alt="" width="300" height="225" /> <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />

Revised 4 years ago
<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"><img class="alignnone" title="hi" src="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg" alt="" width="240" height="180" /></a><img/> [caption id="attachment_713" align="aligncenter" width="300" caption="1/32&quot; 6061 Aluminum"]<img class="size-medium wp-image-713" title="6061" src="http://diylilcnc.org/wp-content/uploads/2011/08/6061-300x225.jpg" alt="" width="300" height="225" />[/caption] </a><img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" /><img class="aligncenter size-medium wp-image-1067" title="chris2" src="http://diylilcnc.org/wp-content/uploads/2012/03/chris2-300x225.jpg" alt="" width="300" height="225" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. <img class="aligncenter size-medium wp-image-903" title="ShoulderBlock_01" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-300x225.jpg" alt="" width="300" height="225" /> <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />

Revised 4 years ago
<img<a href="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg"><img class="alignnone" title="hi" src="http://farm8.staticflickr.com/7207/7030505377_39cd025c04_m.jpg" alt="" width="240" height="180" /></a><img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. <img class="aligncenter size-medium wp-image-903" title="ShoulderBlock_01" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-300x225.jpg" alt="" width="300" height="225" /> <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />

Revised 4 years ago
<img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. &nbsp;<img class="aligncenter size-medium wp-image-903" title="ShoulderBlock_01" src="http://diylilcnc.org/wp-content/uploads/2012/03/ShoulderBlock_01-300x225.jpg" alt="" width="300" height="225" /> <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />

Revised 4 years ago
<img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. &nbsp; <img class="aligncenter size-medium wp-image-1062" title="winterfun" src="http://diylilcnc.org/wp-content/uploads/2012/03/winterfun-300x300.gif" alt="" width="300" height="300" />

Revised 4 years ago
Install<img class="aligncenter size-full wp-image-1060" title="megabot_small" src="http://diylilcnc.org/wp-content/uploads/2012/03/megabot_small.jpg" alt="" width="150" height="150" />Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right.

Revised 4 years ago
Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. &nbsp; <img class="alignnone" title="hhh" src="http://farm7.staticflickr.com/6217/6883688602_b37cea4d15.jpg" alt="" width="375" height="500" />

Revised 4 years ago
Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center and to the right. &nbsp; <img class="alignnone" title="hhh" src="http://farm7.staticflickr.com/6217/6883688602_b37cea4d15.jpg" alt="" width="375" height="500" />

Revised 4 years ago
Install one Belt Tensioner in Shoulder Block Panel 1.  When you stand this panel on end, the Belt Tensioner will be located slightly below center.center and to the right.

Revised 4 years ago
Install a belt tensionerone Belt Tensioner in SBAShoulder Block Panel 1.  When you stand this panel 1.on end, the Belt Tensioner will be located slightly below center.

Revised 4 years ago
Install a belt tensioner in SBA panel 1.  The tensioner should be placed in the off-center hole near the middle of the panel face.  When you stand it on end, the belt tensioner should be slightly below the cetneSBA panel 11.

Revised 4 years ago
Install a belt tensioner in SBA panel 1.  The tensioner should be placed in the off-center hole near the middle of the panel face.  When you stand it on end, the belt tensioner should be slightly below the cetneSBA panel 1

Leave a Reply

You must be logged in to post a comment.